Some Construction Steps for High Speed Door 1, model: HF-J201 2, size: actual scale; 3, curtain: France imported 0.8mm high-density polyester fiber base fabric. The integral curtain can be opened with a transparent window in the middle, and the wind bar is added in the middle to increase the resistance to wind; 4. Door frame material and specification: 6.0mm high quality aluminum alloy track, specification: 140mm*90mm*6mm; 5, roller blind mode: the upper roller roll up the curtain, the two sides to the cabinet contains a wind-proof node to increase the resistance to wind; 6, security device: infrared security photoelectric. Airbag (resistance rebound) automatic derailment function; 7. Control unit: adopts (Danish Danfoss HLP Hailip) external high-performance upgrade control box, built-in vector control mode, high control precision; Hefide servo motor, power supply 220V, power 0.75kw/1400 rev / S , carrying a large load S4 type;

How to maintain the motor of the industrial door? It is forbidden to hammer. If it is loose, it needs to be determined and fixed by tapping. It is necessary to control the force road to avoid problems with the internal parts of the hammer being hammered. Regularly change the motor lubricating oil. After the motor is used for a long time, the lubricating oil in the fuel tank will inevitably have pollutants. If it is not regularly checked and replaced, it may cause frequent vibration and noise during the operation of the industrial sliding door, and even Can not run. The position where the motor is installed should be kept dry and ventilated as much as possible. Do not be in a dark and humid place, so as to prevent the electronic components inside the motor from being corroded by the moisture in the air, causing electric leakage accidents, endangering personal and property safety, and regularly carrying out dust on the motor surface. Clean up to prevent dust from entering the inside of the motor and causing malfunctions. The motor of the industrial door shoul

HOW TO MEASURE THE DOOR OPENING? HONGFA automatic door, here to explain the measurement specifications of the next rolling door installation door hole can be for your reference, the height and width of the door opening size measured by this method can effectively estimate the door area. Electric roller door installation position measurement steps: H-rolling door door height is the distance from the ground to the top of the door and the bottom of the ground beam; B-door width refers to the distance between the left and right sides of the door opening and the distance between the walls of the door and the hole. Generally, it can be divided into single, double and three-car garages; H1-t

High Speed Door Airbag Sensor Test Connect the airbag test, first turn off the emergency stop button, the power box power is turned on, the airbag receiving panel learning button is pressed once, and the signal receiver light is on. Press the pressure hose inside the airbag pocket several times, the signal receiver indicator flashes to receive the memory successfully, repeatedly press the airbag pressure hose, and the receiver light is turned on once every time, the signal connection is completed. Open the rapid door electric control box and stop the emergency. Press the pressure hose inside the airbag bag, and the door body will automatically rise and receive normal signal. Open the electric control box and stop the emergency. Press the pressure hose inside the airbag pocket, and the door body will receive the signal to rise automatically and operate normally. When the electric control box cannot receive the airbag signal: 1. Check whether the battery in the airbag transmitter is exhausted (the side of the curtain weight plate is installed) to replace the battery; 2. Check whe

High Speed Door Control System Installation control system (1) When the control system is installed, it must be in a power-off state and no current is passed. (2) The control system checks the appearance and internal electronic components for damage during transportation before installation, otherwise it may cause serious harm to the user during debugging or use. (3) Non-professionals, do not touch the electronic components on the control panel, especially the processor chip, otherwise the static electricity of the human body will cause permanent damage to the electronic components on the circuit board. (4) Do not allow metal objects such as wire scraps, small screws, drill slag, etc. that are generated during the construction process to enter the control box, otherwise the circuit may be short-circuited. (5) During the process of installing the control box, do not perform any drilling, cutting, grinding and other mechanical processing on the control box. (6) The unused wiring port must be sealed to ensure that the protection level of the control system is IP54. (7) The wire tube should not be exposed or loaded and stretched. (8) The control box cannot be embedded in the wall or installed close to the wall, otherwise it will affect the he

What sets high-speed doors apart? Industrial door systems such as sectional doors or roller doors are often sold under the term "high-speed door". In contrast to classical high-speed doors, these doors are made from metal and do not reach the speeds of a high-speed door. In exchange, sectional doors and roller doors have better thermal insulation than a high-speed door. In the classical u

High Speed Door Installation Manual Part 1:High Speed Door Installation Debugging 1 .Installation Tools 2 .Basic Size 3 - 1 Checklist 3 -2 Schematic Framework 4 .Control Box Size 5 .Checklist 6 . 1-7 Installation Order

How to deal with when the high speed door broken? 1. Problem: Press the quick door control box to run the button or remote control button, the motor does not work and does not rotate. The cause and solution of the problem: (1) The operation mode setting is incorrect, check if P102 is set to 1; (2) The frequency command is not given or the frequency is given less than the starting frequency; (3) The peripheral wiring is wrong, check the peripheral wiring; (4) The input terminal of the inverter is incorrectly defined and does not correspond to the peripheral wiring. Check the parameters of P315-P322. (5) The start button is faulty, the control line is broken, and the control line and button are checked; (6) The inverter is in the protection state, there is no reset, reset first, then start; (7) The motor line is not connected or missing, check the motor connection; (8) Motor failure, check if the motor is faulty; (9) The inverter is faulty and it is checked whether the inverter is faulty. Cold storage dedicated fast

Something need to pay attention to when maintain the electric roller shutter door 1. Why the curtain of electric roller shutter door can't go up and down? There are some factors: (1) There is a foreign object stuck in the track, which causes the curtain to be inoperable. (2) The power supply is faulty, the power supply may be insufficient or the power may be off, resulting in the motor not working. (3) The motor is overloaded and the self-protection function is activated. (4) The remote control is dead or broken. How to repair these electric rolling door failures? (1) check the cleaning track, take out the foreign objects, and regularly check the lower track.

Aluminum roller shutter door installation steps (Need 3 installers): (1) Open the aluminum alloy rolling door box and check the list of accessories and main parts; (2) Finding the site, finding the installation center line on the door hole, and determining the lateral installation reference of the bracket plate, the rolling door and the side rails; (3) Based on the lower edge of the door frame, determine the upper and lower mounting standards of the bracket plate, the spool shaft, the roller assembly, the rolling door and the side rails; (4) Install the bracket plate to the corresponding position above the door frame. After the bracket plate is installed in place, ensure that there is a gap of about 2 mm between the two ends of the roller blind door and the flange for adjustment; (5) Place the reel shaft of the aluminum alloy rolling door on the flange of the bracket plate. The two ends of the reel shaft are fastened with a split pin. One person holds the reel, and the other two adjust the guide rails and sealing strips on both sides of the rolling door. To the installation position (longitudinal beams on both sides of the door);

Industrial sliding door common problems and solutions 1. Damage to the cable Causes and solutions: The cable is slack; in order to avoid the situation worsening, please replace the cable before the drum shaft is wound; 2, The door fell Causes and solutions: spring damage; installation of ballistic spring damage device, according to maintenance records, replace the spring before the maximum number of uses of the spring; 3. The industrial door cushioning elasticity is not good. Causes and solutions: damage to the underlying pad; replacement of the damaged pad; 4, the door panel may be caught in the finger Reasons and solutions: The door panel folding of the sliding door is not installed correct

Some of attentive matters of the maintenance of electric shutter doors 1 The common electric shutter door failure can not lift the curtain, this possible reason: (1) Some foreign objects are stuck in the track, causing the curtain to be inoperable; (2) The power supply is faulty, the power supply may be insufficient or the power may be off, resulting in the motor not working; (3) the motor is overloaded and the self-protection function is activated; (4) the remote control is dead. Or broken up; How to repair these electric shutter doors ? (

Application of Large High Speed Stacking Door In various industrial workshops, we often see the fast door, because it has a fast switch, anti-mosquito and dustproof, and the function of isolating the inside and outside air is widely used, but not all the occasions are applicable to the fast door. Most of the doors are only suitable for door widths up to 5 meters in width and heights are also best within 5 meters. However, in many different functions of the workshop, the size of the door may be much larger, such as a height of more than 6 meters and a width of 10 meters. The door opening, in this way, the ordinary fast door is not applicable. At this time, the best choice is to install the stacking door. Features of large fast stacking doors: The large stacking door has a maximum width of 13 meters, a height of 10 meters, and a maximum wind resistance rating of 7 grades. This is a wind-resistant structure of steel pipes that benefits from the rapid stacking of doors. The door of the stacked doors is made of stainless steel and the curtains are used. T

Application prospects of garage doors The entrance to the garage door in the desert area must be able to meet the challenges of long-term exposure to high wind loads and harsh environments. Therefore, Hongfa automatic door hangar door is an excellent choice for new door installation and replacement of old hangar. Our hangar doors are especially suitable for hangars as well as shipyard facilities and harsh seaside environments. Due to its unique design and structure, the hangar door is very windproof. High security level to meet the security needs of large-scale manufacturing, with built-in security monitoring system and access control. Our hangar doors are designed with few moving parts and require very little maintenance. There is almost no limit to size or configuration. In the design of the hangar gate, the width is not much limited.

Some useful solutions to solve the malfunction problem of medical airtight doors Case 1: The medical sliding door is too noisy during the running process. (1) The noise generated by the friction of the movable door leaf during operation and on the fixed door or the wall can be adjusted appropriately outside the door; (2) The spreader wheel of the airtight door is worn out because it is used for a long time, and only needs to be removed, cleaned and lubricated; (3) Some fixed parts are loose and only need to be reinforced; (4) The box and the guide rail are not installed at the time of installation, and the gypsum board of the ceiling ceiling produces a resonance effect; (5) If the door clamp or the track of the fixed door panel is damaged, it is necessary to remove the box to see if there is any damage inside, and if necessary, it needs to be replaced;

Electric sectional upgrading door First, the scope of use: 1. Applicable to civil and industrial buildings, such as factories, garages, warehouses and other buildings. 2. The width of the door opening is 2400~5400 and the height is 2400~5400. There are 28 kinds of door types for design choice. This type is suitable for areas where the wind load does not exceed 700 pa. 3. Suitable for two wall thicknesses of 240 and 370. Second, the design description: 1. After the door leaf is opened, it moves to the position above the door hole that does not occupy the lower space. The door leaf has a weight component to balance the weight of the door leaf, and reduces the resistance of the switch door leaf. For ease of use, it is designed for electric manual use. Manually shake the sprocket by hand to drive the chain switch door leaf. According to the use requirements, an electric wireless remote control device can be installed to remotely switch the door leaf, and the control distance is within 30 meters. 2, the door type has insulation door and general door for design selection, the insulation door leaf surface material uses the sandwich panel of colored metal insulation material, and the

The Motor for Fire-proof Roller Shutter Doors Firstly, the appearance and parts 1. The outer casing of the rolling up door machine should be complete, without corners and obvious cracks and deformation. 2, the surface of the coating should be smooth, no obvious bubbles, wrinkles, spots, sag and other defects. 3. Parts of the rolling door machine should not be made of flammable or combustible materials. 4, the control device of the roller door machine should be beneficial to the use of staff control. Secondly, the basic performance 1. The rated output torque of the rolling door machine should meet the design requirements. The manufacturer shall provide proof of inspection. 2. The brake of the rolling door should be safe and reliable. The braking force should not be less than 1.5 times of the weight of the rated output torque. The sliding displacement should not exceed 20mm. 3. The rolling door machine should have manual use device. The manual use device should be flexible and reliable, and the installation position should be conducive to operation. When using the manual operation equipment to operate the fire shutter door on and off, it is strictly prohibited to have a sliding collision. 4. The rolling door machine should ha

High Speed Door Servo Control System Introduction Thank you for choosing High Speed Door Servo Control System. Please read this manual carefully before you start to use the system. In this manual you will find instructions for how to set the operating code the controlunit, malfunction diagnostics and debugging, and routine maintenance. Notice:  Before connecting the system to live wire place make sure the power supplyis off.

The Advantages of Hard Fast Doors in the Logistics Channel With the rapid development of the industry, the competition in various industries is very fierce, and all enterprises are improving their work efficiency and output output. In the production workshop of the enterprise, the benefits are paid more attention to. In the case of ensuring the quality, the production must be fast enough. In addition to the competition on the production line, the same is true for the product shipment, especially for foreign trade companies, which may miss the flight due to transportation problems, which may result in the extension of the delivery of this shipment for a week or more. The logistics on the production workshop can use the quick door on the exit of the warehouse, but the entrance and exit of the garage, taking into account various factors such as theft prevention, can not use such products as the soft curtain fast door. At this time, the advantage of the hard fast door is particularly obvious. Compared with the ordinary flap garage door, the performance of the hard fast door on the same logistics channel

The access control system of glass sliding door Glass automatic doors are used more and more in all major places. The most common ones are the front of major supermarkets and the front door of office buildings. The glass automatic doors are not only easy to install, but also more customizable and high-end hotels. They are rotating glass doors, the front door of the office building is an automatic sliding door, the front door of the supermarket uses a curved sliding door, and the office uses an automatic push-pull or sliding door. The wide application of automatic doors also makes people pay more and more attention to safety issues. In addition to the quality and safety of the door itself, it is also necessary to ensure the safety of the property inside the door. For the automatic door opening of the glass door, the following small series recommend several access control to automatically User reference for door installation access control:

Greenhouse fast door application In the modern agricultural system, the greenhouse is one of the most common and widely used buildings. The greenhouse can be applied to agricultural vegetables and fruits, and can also be applied to plants such as flowers and plants. The greenhouse is classified into production greenhouses and experimental greenhouses, commercial greenhouse. Our common vegetable and fruit cultivation greenhouses are production-type greenhouses. Large greenhouses need to control the temperature and humidity of the environment inside and outside the greenhouse. Large greenhouses have been developed very rapidly in recent decades, and they have also driven the use of fast doors in greenhouses. The traditional large-scale greenhouse import and export use ordinary manual doors or glass automatic doors. The disadvantage of this is that as the transportation vehicles continue to enter and exit, not only will the temperature of the greenhouse be lost, but also a large amount of external gas pollution will be brought. The internal environment of the greenhouse has increased the workload of the circulatory system. In response to this situation, many large greenhouses have installed quick doors for entrances and exits. Because the fast doors have the characteristics of fast switching, the above mentioned problems are well solved. The application of the quick door in the greenhouse is also a process in which the two develop and complement each other. After installing a quick

When the 5G era comes, what will be brought about by the technology of Hongfa automatic door fast door? In the past few years, as long as there are electronic or these types of exhibitions, 5G technology and applications will become hot spots in the exhibition, because communication technology and our current life are already inseparable relationship, you have me, I have you. And bring a lot of convenience to our lives. The most common and intuitive technology of 5G network is that the network speed will reach an unprecedented speed. The 5G speed released by Huawei can reach 3Gbps (about 3072Mbps), and the conventional 4G average network speed is 30Mbps. Understand that 4G and 5G differ by a hundred times difference, and the convenience brought by high-speed communication technology is very large. Take the industrial door products as an example. Now we have the common industrial fast door, the safety communication protocol inside is local or local area network, and can not achieve the effect of real-time monitoring and low-latency control. The main reason is that The communication equipment signal speed is not fast, and now the speed of 5G can just solve the original communication speed of industrial doors such as fast doors.

The Common Problems and Solutions of Industrial Sliding Door 1. Damage to the cable: Causes and solutions: The cable is slack; in order to avoid the situation worsening, please replace the cable before the drum shaft is wound; 2, the door fell: Causes and solutions: spring damage; installation of ballistic spring damage device, according to maintenance records, replace the spring before the maximum number of uses of the spring; 3. The industrial door cushioning elasticity is not good. Causes and solutions: damage to the underlying pad; replacement of the damaged pad; 4, the door panel may be caught in the finger: Reasons and solutions: The door panel folding of the sliding door is not installed correctly; reinstall according to the specifications; 5, the protective shell is easy to fall off: Causes and solutions: During installation, the derailing of the protective case is not protected; select the appropriate protective housing support frame to rewind the cable before the problem is removed; 6. The industrial door has experienced a rapid rise: Reasons and solutions: exceed the bearing capacity of the spring; follow the regulation of the number of bearing rings of the spring, and re-commission the number of coils; 7, often foreign thi

The installation steps of the high speed door 1. The relevant personnel who install the quick door must have experience in the installation before the installation, familiar with the design and installation drawings of the quick door, check whether the site is in place before installation, and do other preparatory work before installation, including the temporary need to be used. Parts, installation tools, etc. 2. Before installation, carefully check whether the size of the design drawing matches the size of the site opening; whether the number and appearance of the rail bracket are correct; whether the embedded part of the site is installed, and whether the position of the bracket is accurate or not. 3. The installation workflow is roughly divided into: on-site hole handling, positioning of the elastic line, fixed fast door reel transmission, no-load test, installation of the curtain, installation of fixed rails, testing of the fast door function, cleaning the scene. 4. Hole treatment: Check whether the size of the hole is consistent with the product size. Generally, the width and height of the hole at the site should not exceed 5m. If it is exceeded, it is recommended to install the stacking door to check whether the position and quantity of the embedded parts are correct. 5. On-site positioning of the elastic line: measuring the height of the installation hole, using the i